Sweetwater Series 2 Regenerative Blowers operate at a higher efficiency than traditional regenerative blowers.
The cool-running outboard bearing design allows these units to
achieve higher differential pressures, provide more cfm per horsepower and extend service life. The rugged
die-cast aluminum build is lightweight, compact and extremely quiet. Easy-to-install, close-coupled design
means you can quickly add them to your system. And their internal silencers, washable inlet filter and
outlet flex hose further simplify installation. Oilless and virtually maintenance-free.
Max duty: 76”,
Rate full load AMP: 14.0,
Height W10 Filters: 11.9”,
Outlet Hose Size: 1.5”,
Available in the following models: SST10,15,20,25, 30-230, 35, 40,40-230, 45, 50, 55, 60-80.
Whitewater air pumps work well in deep applications. They are virtually silent and feature a rugged,
weatherproof, aluminum housing. Pumps have a 3/8" outlet and a 4' power cord. 115V/60 Hz Available model and specifications:
Model V201: Volts: 115, Hz:60, Watts: 15, (L)9”x(W)7¼”x(H)7”
Model V301: Volts: 115, Hz: 60, Watts: 25, (L)9 5/6” x(H) 8”
These air pumps have aluminum covers and internal noise-absorbers.
Although the pump housings are waterproof and designed for outdoor use.
Pumps include 6' power cord, 3/8" hose barb, flexible outlet adapter,
and outlet adapter to aquarium tubing (3/16") Model 9720: Volt: 115, Hz: 60, Watts: 25, W/Adapter: 6 – Outlet, (L) 7½ x (W) 6” x (H)7”
Available in Models: 9720, 9730, 9720D and 9730D.
WhitewaterR air compressors are designed for indoor use only.
Outlet is 3/8" barb; 6' power cord. Diaphragms typically
last one year at the highest pressures, longer at lower pressures. Model LT24: Voltage :115, Hz: 60, Watts @2PSI: 60, (L)10”x(W)5¼”x(H)7”
Available in Model: LT24 and LT19.
The system includes three air diffusers that go into the water; and air is delivered to each
diffuser via included flexible .” air supply lines. Each of the .” flexible air supply
lines is connected to customer-provided .”
PVC pipe which is installed overhead or along the tank wall. CBS10: Supports up to 10lbs of Minnows per diffuser (8” long) air pump is for indoor use only.
Available in model CBS20 and CBS3 that support higher numbers of diffusers.
Sweetwater® glassbonded diffusers are compatible with
economical low-pressure blowers.
They produce a uniform medium/fine bubble and are very resistant to clogging. Body : 2,000°F Glass-Bonded Silica
Maximum Pore Size : 140 Microns (.0055 Inches)
Bubble Size: 1–3 Mm (.04–.15 Inches)
Nominal Particle Retention : 50 Microns
Service Life at pH Below 8.0: Unlimited
Flexural Strength: 2,500 Psi
Available models in AS, ALS, ALR and ASW series.
Point Four diffusers use a specially developed, ultra fine pore
ceramic plate that produces a cloud of extremely fine bubbles
of approximately 100–500 microns; far superior to airstones,
porous hose or membrane type designs. The flat plate design
ensures uniform bubbles across the entire surface and minimizes
bubble coalescence to achieve an absorption rate in excess of
80%, depending on depth and flowrate. Bubbling Pressure is 25 to 35 psi.(1.7 to 2.4 bar). Model: 1DMBDC900 with Aluminum base, Diffusing area of (L) 39¾”x(W) 3¼” Rec. Operating range: up to 9/19.5, Maximuim flow rate @ 50PSI(3.5 Bar) LPM 27 and SCFH 58, Gas Inlet Connection: ¼”FEMALE. Available in Model: 1DMBDC100, 1DMBDC300, 1DMBDC600, 1DMBDC120.
PADDLE WHEEL AERATORS, FOR AQUACULTURE & WASTE WATER
Excellent oxygen transfer and circulation. These high-quality paddle wheels feature high-efficiency 60 Hz motors and high-quality
gear reducers to ensure a long service life. The frame, drive shaft and hardware are 304 stainless steel—all
compatible with salt water. Power cable not included. Paddle wheel aerators are an excellent choice
for medium and large ponds where movement of oxygenated water away from the aerator is most important.
The entire unit, including gear reducer and motor, Motor, Motor Cover, Frame, Drive Shaft & Hardware, Paddle Wheels. Model PW21 with HP:2, Voltage: 230, Hz: 60, Phase: 1, Running AMPs: 9.98. Available model: PW11-AQ, PW23, PW33.
High efficiency TEFC design with Stainless steel fan cover and T-box,
Motor Cover made of high density, water-proof polyethylene, Impact and high wind resistant
Gear Reducer (C) of High quality ALBC 3 wheel gear and S45C carbon steel, worm shaft
Frame, Drive Shaft & Hardware: 304 Stainless steel to provide rust resistance and longer life
Paddle Wheels (G): Eight blade, fiber-reinforced nylon
Floats (A): One-piece, blow molded, leak proof polyethylene floats, Strong but lightweight for easy handling
Oxygen Generators are specifically designed for reliability, energy efficiency, and ease-of-use.
• Self-contained (internal air compressor)
• Transportable roller base design
• Easy to install and maintain
• Low operating cost
• High-impact polystyrene enclosure
• Advanced engineering
• Time-proven reliability The ability to deliver up to 95.5% oxygen concentration make it a perfect fit for many aquaculture applications such as fish farming, laboratory experiments, aquaponics and hydroponics. Model available are the ONYX series, ONYX Plus series and ONYX Ultra series.
The design uses a propeller inside the lift tube, increasing the pumping efficiency. Low-restriction
slots spray the lifted water, providing excellent aeration and very popular for live fish transport. Available in Model V1, V1S, V2S.
Model V1 Aerator, Pumping Rate (GPM):75, Volts: 12, AMPS: 10@12V, Tube Length: 20".